カブのブレーキケーブル交換するよ! その2 / I try to change the brake cable of my super cub. part 2
はいこんにちやってまいりました〜。
Hi, I'm yyoumgstar
今日はもちろん昨日の続きです。
Today, I'm gonna write about changing the brake cable.
ということでね。
That's how.
まずは、ネジザウルス氏をつかって、つぶれたネジを外していきました!ネジザウルス氏すごい!さいこう!
First, screw the broken one off using Mr. "neji-saurus". great "neji-saurus" !!
そしてー、ハンドル関係のボルト、ナットを3ヶ所緩めていきます。
and then, loosen the bolt and nuts of handle.
8 mmレンチで一個
a bolt with 8 mm wrench.
12 mmでこれを二つ
two nuts with 12 mm wrench.
続いてー、ブレーキケーブルを下から(前輪についてる方に)引っ張って抜いていきますよ!
とりあえず切れた中身のワイヤ出てきた。
next, pull the cable down.
I got the broken wire.
この辺なかなかだるかった。
ここの金属が邪魔で抜けてこない。
It is difficult to pull it off.
This metal part is bother.
そんな時はなんでも切れると噂のニッパーさんでやっつけてしまいます。
cut it with a nipper.
そうするとするするとケーブルが抜けました!
Then, I could pull off easily.
ででんっ
あたらしいやつ!
The new one !!
これの先っちょをテープでアレします。
I do something for the tip of it with tapes.
先っちょかぶせたら、ハンドルロックの横のところに挿入れていきますよ!
After that, insert it from the side of handle-lock.
意外とスルスルと行くんだけど、途中横道にそれることがあるので、棒的なもの(マイナスドライバーとかでいいでしょう)道をちょくちょく修正してやります。
I could do easilier than I thought. But we should adjust the route of it with something stick (minus screwdriver or something).
あっ
というまに〜
in no time.
ちょっと養生テープじゃ、あれだったから、テープ界のユーティリティプレイヤー、ビニールテープにするわ。
Masking tapes was worse. Vinyl tapes was better for it.
ここ難関。
さっき、金属のところをぶった切らなきゃいけなかった隙間に通さなきゃいけません。
it is difficult to insert it.
ここめちゃくちゃ疲れた。
I was exausted.
通ったらあとは、全てを元どおりにするだけ!
after through it, fix as before completely.
さーて、最後にケーブルを前輪につけよーっと。
at the last, I'll get cable into front tire...
あっ
oooooops !!
ブレーキケーブル間違えて注文してた(´・ω:;.:...
— 若星 (@yyyoungstar) 2014, 11月 16
まあ、何とかなるでしょ。ライトもつくし、ブレーキもきくからとりあえずこれで!
well... It'll work... light is ok. and brake also work correctly.
作業は以上!
That's it !!
ケーブルに関しては、型番までちゃんとチェックしてたのに、なぜか発注の時間違えた!
反省!
About the cable... I checked correctly but I had a mistake.
Reflect seriously....
もう3年くらいやりたくないです!
I don't wanna do it for 3 years !!
それじゃあまた!
Thank you fo reading !!